• 집
  • 에 대한
    • 제품 및 생산

      다음 생산 단계를 찾으세요.
      생산 라인

      제작하려는 케이블부터 시작하세요.

      내부 구성 요소가 노출된 옥외용 광케이블

      광케이블 제조 장비

      노출된 트위스트 페어가 있는 블루 LAN 케이블

      꼬임쌍 케이블용 장비

      파란색 절연 피복 동선

      절연 전선 및 케이블용 기계장치

      예비 부품 및 지원

      HONGKAI 기계 장비의 교체 부품.

      생산 라인별 부품 살펴보기

      사진, 명판 및 부품 번호를 확인하세요.

      기계 세부 사양, 사진 및 수량을 보내주십시오.

      케이블 및 재료

      케이블 구조와 입력을 살펴보세요.

      실외용 광케이블의 단면 및 내부 구성 요소

      광섬유 케이블 유형 찾아보기

      금속 주걱이 있는 흰색 및 검은색 고분자 펠릿

      광케이블 생산용 재료

  • 블로그
  • 연락하다
가이드 케이블 기계 장비 선택 가이드

AWG 선규격: 케이블 기계 구매자가 반드시 명시해야 할 사항

AWG 번호는 완전한 기계 입력을 정의하지 않습니다. 장비 비교 전 도체 구조, 개별 와이어 크기, 실제 외경, 릴 기하학 및 테스트 증거를 별도로 확인하십시오.
Conceptual solid and seven-wire insulated conductors beside the question Which Wire Fits Your Line.
귀사의 라인에 적합한 와이어는 무엇입니까?

A factory may receive an enquiry for “22 AWG wire” and still lack the information needed to select its cable machinery. The gauge does not say whether the factory will buy a finished conductor, draw individual wires, assemble strands or apply insulation.

Use AWG as one field in the conductor specification, not as a substitute for material, strand construction, actual dimensions, reel drawings or acceptance requirements. Each production stage needs the dimensions of the material that actually enters and leaves it.

This guide is for factory owners, production managers and technical buyers preparing machinery enquiries. It does not select a conductor for an electrical installation or provide current-carrying, circuit-protection or installation-code advice.

Why the Same AWG Can Mean Different Outside Diameters

AWG means American Wire Gauge. ASTM B258 defines nominal diameters and cross-sectional areas for AWG sizes of solid round wire. Its scope is not a finished-cable diameter table.1 “스트랜디드(stranded)”라는 단어를 추가하는 것 역시 와이어의 고유한 배열을 정의하지 않는다.

A complete product model tied to an identified specification may already provide the construction and dimensions needed for an enquiry. In that case, send the specification and its revision with the model. An AWG number by itself is only the gauge designation; it does not identify the conductor metal, coating, strand arrangement or finished-wire diameter.

Keep material and construction as separate decisions. Copper or tinned copper describes material or coating; solid or stranded describes how the conductor is built. The customer’s required product determines these choices. Whether the factory buys that conductor or makes it in-house is a further decision about the machinery scope, not a property of the AWG number.

게이지 옆의 구조를 읽으십시오. 다음과 같은 지정은 22 AWG, 7/30 identifies a 22 AWG conductor made from seven 30 AWG wires. The “30” is the individual wire’s gauge, not a diameter in millimetres. For a solid conductor there is only one wire, so the individual-wire diameter and the uninsulated conductor diameter refer to the same physical object.

Conceptual solid and seven-wire conductor sections separating metal area, conductor outside diameter and insulated-wire outside diameter.

도체 구조 및 외부 피복의 개념적 비교. 출시된 제품의 치수는 표에 유지되며, 도면은 제조 도면이 아닙니다.

Published products make the distinction concrete. Alpha Wire lists the following two tinned-copper hook-up wires under the same 22 AWG designation.23

Published product 도체 구조 표시된 도체 직경 표면 PVC 벽 Listed insulated-wire diameter
Alpha Wire 3051/1 Solid, 22 AWG 0.025 in 0.016 in 0.057 ± 0.002 in
Alpha Wire 3051 Seven wires, 22 AWG (7/30) 0.030 in 0.016 in 0.062 ± 0.002 in

These are the manufacturer’s stated values for those particular products, retained in their published units. They are not universal dimensions or tolerances for all 22 AWG conductors, and they are not HONGKAI production results. The useful comparison is that the gauge and nominal insulation wall are the same while both the conductor diameter and the insulated-wire diameter differ.

For equipment selection, keep three quantities separate:

  • Metal cross-sectional area: the area of the conducting material, expressed in a specified unit such as square millimetres.
  • Conductor outside diameter: the outside envelope of the uninsulated solid or stranded conductor.
  • Insulated-wire outside diameter: the envelope after the specified insulation has been applied.

The spaces between round strands explain why a stranded conductor’s outside envelope cannot be treated as a solid metal circle. For an ideal set of equal round wires, the sum of the individual wire areas is n × π × d² / 4, where n is the wire count and d is the individual-wire diameter. This is a geometric sum, not a rule for assigning an AWG size or a finished-conductor acceptance method. The conductor’s actual arrangement, lay, coating and any compaction still need to be specified.

Note: Do not relabel a rounded AWG-to-mm² comparison as an approved metric conductor specification. Keep the original designation, governing specification and controlling dimensional units visible; an engineering comparison is not permission to substitute another product.

Give Each Machine the Dimensions It Actually Uses

A supplier cannot select a complete production route from the final AWG number alone. First decide which material the factory purchases and which transformation the proposed equipment must perform.

If the factory buys a conductor ready for insulation, conductor drawing and assembly may be outside the purchase. If it buys individual wires, the required conductor construction determines the assembly stage. If it starts with larger wire or rod, the drawing route needs its own input and output definition. These are alternative scope boundaries, not a recommendation that every factory should own every operation.

In HONGKAI’s enquiry assessment, the first distinction is therefore between buying ready-made conductors and purchasing equipment to make them. A broader mix of wire sizes can be a reason to evaluate in-house drawing, while limited demand or a small product range may make that investment difficult to justify. Neither condition establishes savings on its own: compare the actual product mix, required volume, available feedstock and quoted purchase and operating costs before adding a drawing machine.

Three material starting points: larger feed for drawing, individual wires for conductor assembly, and purchased conductor for insulation.

Conceptual material handovers for drawing, conductor assembly and insulation. The purchased scope determines which stages are required; these are alternative starting points, not a requirement to own every operation.

Operation under review Product data to provide What the offer needs to resolve
Individual-wire drawing Feed material and condition, starting diameter, required individual-wire diameter and tolerance, required final condition The reduction and finishing scope, including whether annealing is part of the offer
Bunching or stranding Number and size of individual wires, material and coating, required construction, lay requirements and finished conductor envelope 제안된 조립 방식이 지정된 입력값으로 해당 구조를 구현할 수 있는지 여부
절연 사출 Actual incoming conductor size range and surface condition, insulation compound, required wall and finished-wire dimensions Material-processing scope, guide and tooling review, centring checks and the proposed trial product
Pay-off and take-up The package entering and leaving each stage, dimensioned reel drawing, empty and loaded mass, winding and handling requirements Physical fit, support and drive arrangement, controllable handling and transfer to the next stage

For drawing, do not send only the area of the assembled conductor. A drawing proposal needs the individual wire that must be produced. For assembly, keep individual-wire diameter, wire count and finished conductor diameter together in the same specification. This three-part check makes the intended input and output explicit; the supplier must still confirm the required construction and assembly method, not simply match one outside diameter in a catalogue.

Bunching and ordered stranding should not be treated as interchangeable catalogue names. For example, ASTM B8’s public scope describes concentric-lay conductors with a centre surrounded by helically laid layers.4 Whether that specification applies is a product-design decision; its construction cannot be replaced by an unspecified bunch merely because the nominal size is similar.

An extrusion enquiry then needs the conductor that will actually pass through the crosshead. Identify whether its stated diameter is a design target, a measured value or a permitted range. Keep the insulation compound and wall requirements in separate fields rather than deriving them from AWG.

HONGKAI’s bunching equipment selection page separates individual-wire details, finished-conductor construction, lay and output-package requirements. Those are distinct selection inputs, not one interchangeable “wire size”. The page is a family-selection reference, not a project-specific operating-range table; the selected construction and the offered machine still require confirmation. No model range, speed or delivery experience is assumed in this guide.

The result of this step should be a stage-by-stage input record. Where a value is not known, mark it as unresolved in the enquiry instead of allowing a supplier to fill it with an unacknowledged assumption.

Keep the Specification Attached to the Reel and the Test Result

Dimensions describe the product, but a useful equipment enquiry also identifies how that product will arrive, be handled and be checked. A conductor sample without a drawing revision or reel identity is difficult to connect to a later machine trial.

Reel Geometry Is a Separate Input

Identify whether the customer will use steel reels, wooden drums or another agreed package; do not leave the material and construction implicit. Provide the reel’s flange diameter, barrel diameter, usable winding width, overall width and bore or mounting details. Also state the empty mass, maximum intended loaded mass and the proposed loading method. A single nominal reel-size label does not communicate all of these features.

Compare the same drawing at the upstream take-up and downstream pay-off. Ask the supplier to identify any required adapter, transfer or rewinding stage explicitly. Do not assume that a reel can be reused merely because its flange diameter fits both machines.

Front and side reel diagrams showing flange diameter, bore, barrel diameter and usable width, with one sample linked to separate dimensional and electrical records.

Illustrative package-interface and sample-record relationship. Reel dimensions, loading arrangements, dimensional checks and electrical test responsibilities must be agreed for the selected product.

For a trial, retain the package identification with the conductor construction and the winding requirements. Where handling stability matters, define the package conditions that must be demonstrated rather than approving the arrangement from an unloaded reel alone. These are proposed purchase checks, not a universal test sequence or an equipment-load rating.

Manufacturing Checks and Electrical Tests Need Separate Evidence

For a conductor-assembly trial, identify the incoming individual-wire size, wire count and required assembled diameter. For the specified insulation or sheathing operation, identify the incoming conductor and the required finished dimensions. The purchase specification should say which dimensions are measured, how they are measured and which product-specific limits govern acceptance.

These manufacturing checks are not substitutes for the finished wire’s electrical tests. Define who supplies the additional instruments, performs each test and issues the result. If test equipment or testing services are included in the machinery contract, list them explicitly; otherwise, make the customer’s separate testing arrangements visible. Separating the evidence does not remove either party’s agreed responsibilities.

An outside-diameter check does not measure electrical resistance. ASTM B193’s public description treats specimen dimensions, resistance measurement and correction to a reference temperature as parts of determining conductor-material resistivity.5 That does not make B193 the automatic release standard for every finished wire.

For the selected product, ask the responsible engineer to identify the applicable resistance requirement and test method. The resulting record should connect the sample identity, measured length, test temperature, instrument and method to the reported result. If a correction is used, retain its basis. State whether the reported number is an actual measurement, a normalized result or a catalogue nominal value.

Keep dimensional and electrical evidence distinct. The manufacturer’s data for a particular construction can help define an enquiry, but copying a catalogue value into a trial record does not demonstrate that the trial conductor met it. Likewise, a successful resistance result does not by itself prove the strand count, insulation wall or reel interface.

Evidence to request: One identified conductor specification, its material and construction record, the relevant dimensional measurements, the agreed electrical or mechanical test results, and the reel drawing used for the trial. Each acceptance limit must point to the approved product requirement, not a generic AWG chart.

Build a Conductor Record That Two Suppliers Can Quote Consistently

The final purchasing document should make it difficult for two suppliers to interpret the same gauge differently. HONGKAI’s practical starting point is a clearly identified product and a stated production requirement; the same definition should carry through the equipment configuration and contract to the acceptance criteria. Organize it around one conductor construction at a time, with the following linked records:

  1. Product identity: the cable or wire application, drawing number and revision, conductor designation and governing specification.
  2. Material and construction: metal, coating and condition; solid or stranded; individual-wire count and size; assembly method and lay where required.
  3. Stage dimensions: the actual input and output dimension at every purchased operation, with units, limits and measurement basis.
  4. Package interfaces: incoming and outgoing reel drawings, mass limits and transfer or loading arrangements.
  5. Output and demonstration basis: the required production output, its units and associated product; materials and reels for the trial; measurements, acceptance criteria and responsibilities.

Conceptual seven-wire section and reel feeding one specification record used by two suppliers for comparable offers.

Conceptual quotation comparison: both offers must refer to the same conductor construction, dimensions and package interfaces. The blank records are not actual quotations or acceptance results.

“22 AWG machine” leaves all five records open. “Insulation extrusion for an identified, purchased 22 AWG conductor” at least defines the operation and starting point, but still needs the conductor envelope, compound, wall, finished dimensions and packages before it becomes a complete specification.

If an alternative construction is acceptable, give it a separate record. Do not let a different strand count or conductor material disappear into a general statement that both products have the same AWG. Ask the supplier to identify which tooling, handling conditions or trials change with the alternative.

When comparing quotations, trace each offered machine back to the operation it owns and the conductor record it accepts. Separate the factory’s current products from future options. A demonstrated operating condition for one conductor is not evidence of performance across an unspecified gauge range.

Keep the product drawing, configuration sheet and contract consistent when the required construction or output changes. Name the trial product and conditions beside the output requirement, and attach the agreed acceptance criteria. A target in an enquiry is not an independently demonstrated result until the agreed trial and measurements support it.

The practical output is not a larger conversion chart. It is an agreed description of the metal, the construction, the physical envelope and the package at each handover. Once those inputs are fixed, machine selection and acceptance discussions can refer to the same product.


  1. ASTM B258-18(2026), official scope and edition record. The public record concerns nominal AWG dimensions for solid round wires; it is not a finished-cable specification. This guide does not reproduce the standard’s dimensional tables. ↩

  2. Alpha Wire 3051/1, product construction. Product-specific solid-conductor, wall and insulated-wire dimensions, checked on 29 October 2026. ↩

  3. Alpha Wire 3051, product construction. Product-specific seven-wire, wall and insulated-wire dimensions, checked on 29 October 2026. These two examples illustrate specification differences, not a recommendation to copy either product. ↩

  4. ASTM B8-23, official scope. The public description distinguishes concentric-lay construction; applicability and detailed requirements must be selected for the intended product. ↩

  5. ASTM B193-25, official method overview. The public description identifies dimensional and resistance measurements and temperature correction. It is not a substitute for the applicable full method or the finished product’s acceptance requirements. ↩

Next Step

Send your target cable, production capacity and factory conditions. We will confirm what needs to be verified before quotation.

프로젝트 상담하기 Print this guide
프로젝트 문의

International Sales & Project Director

Article Methodology
  • Cable production-line project discussions with international buyers
  • Supplier technical document and drawing reviews
  • Factory layout, utility and capacity planning
  • FAT, delivery and commissioning experience
Content Basis

Prepared from HONGKAI project work. Figures, standards and market statements are rechecked before an article is featured.

프로젝트 시작하기

케이블 사양을 보내주세요

Tell us the target cable, production capacity, factory conditions and current equipment scope. We will confirm what needs to be verified before a quotation — not just send a price list.

Reply within one working day
Shenzhen & Dongguan, China

케이블 생산 참고 사항

케이블 제조, 장비 선택 및 문제 해결에 대한 월간 노트와 HONGKAI 생산 라인 관련 가끔 업데이트를 받아보세요.

견적을 요청하세요

우리는 24시간 이내에 당신에게 대답할 것입니다!!!